Show Menu

Defrosting a Manual Defrost Laboratory Freezer Cheat Sheet by

8 Easy Steps to Defrost a Manual Defrost Laboratory Freezer
freezer     steps     laboratory     maintenance     defrosting

Introd­uction

Laboratory cold storage and the protection of sensitive samples rely heavily on temper­ature unifor­mity. Manual defrost freezers will ultimately provide the best temper­ature uniformity when maintained properly, but manually defrosting a freezer can be strenuous and time consuming. Whether your laboratory consists of ultra low temp freezers, deep chest freezers or even standard upright and underc­ounter freezers, this article will help simplify the manual defrost process

When should you defrost your freezer?

This question relies on your labora­tory’s standa­rds­/pr­efe­rences and what you are storing in your freezer. You must constantly monitor your freezers frost and internal temper­ature in order to ensure your samples are safe. When frost builds up in a freezer it begins to insulate the walls which will eventually warm the internal chamber:
More Frost = Less Temper­ature Unifor­mity.
A good rule of thumb is to not let the frost build up more than ¼ to a ½ inch of ice. If any temper­ature fluctu­ations being to occur and frost build up is visible in your freezer, it’s probably a good time to defrost. Defrosting will not only save your samples and your research, but will also extend the life of the freezer and lower energy costs.

Before you defrost, PLAN AHEAD!

A few things you will need to plan before manually defrosting your freezer:
2 Day Process: Make sure you plan for at least 48 hours of freezer downtime
Back Up Freezer Availa­ble: Make sure there is a freezer available that is capable of storing the samples at the same temper­ature. You will be removing all contents from the freezer that will need to be defrosted, don’t start the process without having your back up freezer up and running at the proper temper­ature.
Alert Your Peers: Most likely there are multiple people using your lab, the freezer you are defrosting and the samples within that freezer. Make sure all laboratory personnel know which freezer(s) you will be defrosting and where the samples will be tempor­arily stored.
Once you have a scheduled timeframe, a backup freezer set up, and alerted all personnel, you are ready to begin the defrosting process!
 

Begin Defrosting

1. Remove Everything from Freezer: Remove all contents from the freezer you are about to defrost and place them into the back up freezer. Make sure this freezer is at optimal temper­ature for the specific samples you are storing.
2. Unplug the Freezer: Unplug your freezer to begin the warm up/melting process. It is best to do this in the morning so you can monitor any water or ice runoff during throughout the day.
3. Hold Door Open: Use a bin/prop. For doors that are higher up, I like to use a folded wad of paper towels (or cardboard) jammed between the two door hinges to force the doors to stay open
4. Let it Melt Away, NEVER CHIP AWAY: Melting can take a while and it has to be monitored and cleaned up frequently so water doesn’t run everywhere in the lab. To speed this up, work from the top down and spray (or sponge) hot water on the coils and wire racks and set up a reservoir system for the water to run into a bucket or pan. NEVER USE SHARP OBJECTS TO CHIP AWAY AT THE ICE! THIS COULD PERMAN­ENTLY DAMAGE THE FREEZER!
5. Clean if Dirty: Baking soda and hot water work or for a more intense clean, use 10% bleach solution.
6. Dry it Out: Once the ice has completely melted make sure the freezer is completely dried out so ice does not reform once the freezer is plugged back in. Wipe the insides of the unit down to ensure they’re completely dry.
7. Plug it In: Place your freezer back in its normal space and plug it back it to turn it on. Allow for optimal time in order for the unit to come back down to the desired temper­ature. Monitor the temper­ature.
8. Replace Conten­ts: Once the freezer reaches the set temper­ature, you may now place your sample inventory back into the freezer.

If Contains Radioa­ctive or Biohaz­ardous materials

Radioactive: Collect some ice, and test it with a liquid scinti­llation counter. If the melted ice registers greater than 3 times background (compared to tap water control), collect the ice as radioa­ctive waste and label it for pickup according to your lab’s safety procedures and decont­aminate the unit as approp­riate.
Biohazardous: Collect the ice and add 1 part bleach to 9 parts melted ice. After 20 minutes pour into drain, ideally in a fume hood.
Chemical: ensure the unit has been carefully wiped down and the paper towels used to clean the unit are disposed of approp­ria­tely.

Download the Defrosting a Manual Defrost Laboratory Freezer Cheat Sheet

1 Page
//media.cheatography.com/storage/thumb/davidpol_defrosting-a-manual-defrost-laboratory-freezer.750.jpg

PDF (recommended)

Alternative Downloads

Share This Cheat Sheet!

 

Comments

No comments yet. Add yours below!

Add a Comment

Your Comment

Please enter your name.

    Please enter your email address

      Please enter your Comment.

          Related Cheat Sheets

          Holidays / Vacations Cheat Sheet
          Cooler/Freezer Diagnostic Protocol Cheat Sheet

          More Cheat Sheets by Davidpol