Show Menu

Tips for Cylinder Maintenance Cheat Sheet by

Tips for Cylinder Maintenance
tips     maintenance     hydraulic     cylinder

Introd­uction

Proper, consistent cylinder mainte­nance is necessary to keep your fluid power systems running smoothly and effici­ently. Following these five tips is a step in the right direction.

1. Keep your oil clean

This should go without saying, but I wouldn’t have to say it if the majority of hydraulic failures weren’t still from contam­inated oil. Filter your danged oil. Dirt particles love to move back and forth inside a cylinder, so it’s especially important to ensure oil is clean the first time it makes its way into your cylinder.

2. Inspect your cylinder regularly

Have a look at the condition of the rod for corrosion, pitting and uneven wear. Corrosion could signal excessive moisture, either ambient or within the fluid. The latter scenario is worse, as it spells disaster for your entire hydraulic system. Rod corrosion will accelerate seal wear, as friction damages the rod seal and wiper. Pitting on the rod can occur from corrosion, but also from physical damage, which will also lead to seal damage

Uneven wear of the rod is often a result of misali­gnment. Side load causes the rod to rub on one side of the bearing, which can premat­urely wear the bearing, seal(s) and rod itself. In most cases, a corroded and damaged rod can be re-chromed and/or polished to refinish it. If the rod can’t be repaired, it can be manufa­ctured by any cylinder repair shop. Before re-ins­tal­lation, it would be wise to remedy the problem causing the damage in the first place, or you will find yourself in the business of changing the cylinder often.

3. Rotate your cylinder

If downtime is an absolute imposs­ibi­lity, you may want to keep a set of spare cylinders you rotate into service on a regular basis. This will keep your cylinders fresh in spite of high risk particle contam­ination or extreme operating condit­ions. Once one cylinder is removed from service, it can be disass­embled, inspected and repaired if required.

When a cylinder is in pieces, it’s a good idea to replace all seals, since they’re typically very econom­ical. Inspecting the internals of your cylinders on a regular basis also gives you clues to the condition of the rest of your hydraulic system. The occurrence of varnish, for example, could mean your oil is running contin­uously hot, and you may need to address operating temper­ature.
Also, a physical inspection of the piston and cap can tell you if particles have been trapped within the cylinder. If it looks like someone was beating your piston with a ball peen hammer, then I can guarantee a chunk of metal has been slapping around inside for months or years. And if it made its way into your cylinder, it existed elsewhere in the system, too.
 

Hydraulic Cylinder Seals

4. Service your access­ories

The brackets, clevises, rod eyes, ball joints or other connec­tions to a hydraulic cylinder are nearly as important as the cylinder itself. When a pivot pin or clevis is worn, there is excessive slop and play in the joints of the cylinder. This will cause misali­gnment, which could lead to rapid wear or catast­rophic damage in some cases.

If you have a high precision machine, even a few thousa­ndths extra clearance between each joint can cause jerky, inaccurate motion and vibration. When a cylinder is removed for servicing, it is a best practice to inspect and replace the access­ories, if needed. A pin is only a few bucks, and is meanin­gless compared to a thousand dollar NFPA cylinder. Just as with other parts of your hydraulic machine requiring lube, grease the cylinder joints on a regular basis to prevent uneven or excessive wear. An ounce of prevention goes a long way.

5. Inspect your lube oil system

If you are running pneumatic cylinders, which often need their own source of lubric­ation, inspect and service your lubric­ation system, as needed. A basic system will have a lubricator built into the filter­/re­gulator assembly, which is fairly reliable. However, no lube oil can be provided when the reservoir is empty. Inspect the oil level regularly, and top off as needed.

Even a reservoir full of oil provides no guarantee your lubricator is working, so you may need to test your oil line exiting the FRL by hooking up a blow gun and spraying a white paper towel. If there is a patch of oil on the towel, you’re good to go. If it is dry, you may have to remedy a clog in the lubric­ator, or replace it if it cannot be fixed.

When testing any lubric­ation system, check that excessive amounts of oil aren’t being introduced into the system. I’ve seen lube systems introd­ucing so much oil as to hydrolock a pneumatic cylinder, preventing it from cycling full stroke rapidly. Only a fine mist is required to help an air cylinder overcome friction.

Download the Tips for Cylinder Maintenance Cheat Sheet

1 Page
//media.cheatography.com/storage/thumb/davidpol_tips-for-cylinder-maintenance.750.jpg

PDF (recommended)

Alternative Downloads

Share This Cheat Sheet!

 

Comments

No comments yet. Add yours below!

Add a Comment

Your Comment

Please enter your name.

    Please enter your email address

      Please enter your Comment.

          Related Cheat Sheets

          10 Ways to Ruin your Hot Tub Cheat Sheet
          Tips for Proper Bearing Maintenance Cheat Sheet

          More Cheat Sheets by Davidpol

          Kotter 8 Step Process leading Change Cheat Sheet